RapidAir MaxLine 3/4" Compressed Air Piping System Master Kit

I installed about 90 feet of 3/4" line with 3 stations.

Two were in the garage, where my old Sears (4.5 CFM) compressor was connected. The line then went through a floor joist, then down to the lower walk-out basement where my work shop is.

I needed to use a 1 1/4" spade bit because of the stiffness of the air tubing. It was also difficult to control the slope with all the other services running with the joists.

I installed one drop in the workshop, and at the end of the run I connected my new Quincy 12120P (8.7 CFM) compressor. The small bead blaster really works great. This dual air source give me over 12 CFM.

I installed about 90 feet of 3/4" line with 3 stations.

Two were in the garage, where my old Sears (4.5 CFM) compressor was connected. The line then went through a floor joist, then down to the lower walk-out basement where my work shop is.

I needed to use a 1 1/4" spade bit because of the stiffness of the air tubing. It was also difficult to control the slope with all the other services running with the joists.

I installed one drop in the workshop, and at the end of the... more

I purchased this system after reading about it on a few blogs. After a little research, I decided to purchase the 3/4" shop set up. It is fantastic.

It went together fast and easy, no problems. No need for extra elbows if you have room to bend a corner; and if you have an offset, just put one in!

Thanks for a great product!!

I got around to installing the kit today, and what a breeze. I ran 60' with 3 drops.

The only leak I had was a plug on the back of one manifold- I forgot to tighten it. I used Rectorseal #5 on fittings.

I am completely satisfied with the system and highly recommend it.

Thanks for a Quality product.

Really impressed with overall quality of kit. I can tell, I won't have any problem with the hose conforming to where I place it.

There have been absolutely no problems with the hose being pliable and holding it's shape. I'll update review after total install, but for now couldn't be happier with the quality of the kit.

This is an exceptionally well made and designed kit. With all fittings required for 3 drop lines and outlets for each , This kit installs easily without having to purchase extras fittings. Tech tip from my experience (unroll and straighten hose to length on floor as you go, then hang in supplied clips) Follow instructions for leak free connections. Would buy again!!

I found this product to be excellent and easy to install. I would strongly recommend it.

The air volume is great, and the price and time it took to get to me was outstanding.

I'm a very satisfied customer.

A much needed and long anticipated upgrade for our 5 bay shop. Easy to install. No surprises. A great product.

Yesterday I finished the airline project and fired up the compressor to check on leaks.

I started to install the MaxLine system about 3 weeks ago with just me and 3 Saturday. I went with the 100 ft 3/4" system for more volume and CFM and watched the video on YouTube to get the gist on installing the system. The installation was easy and repetitive, once you did one "drop down" you just repeat the process until you are done.

My system has 7 drops (coupler plug ins) with a nice Devilbiss air dryer & regulator unit. My intention is to get another 100' to make a loop and to add 3 more "drops" as well as getting some of the 1/2" line to have the air line drains, discharge at the floor instead of all over the wall.

So the only thing that was tough was rolling out the pipe to be straight. I am starting up a training center for Auto Body repair and I wanted a classy look. The way this was achieved was to get the pipe close to straight then install it. Once I had the main line and drops mounted I went back and straightened everything. The clips that anchors the line work well, I went with one every 4 feet and where there was a drop (tee fitting).

So yesterday after installing all 7 of the coupler blocks with couplers I fired up the 80 gallon Puma compressor that builds 175 psi (also purchased from Air Compressors Direct) and listened for air leaks. There was none.
Very impressed, in the past I have used copper and black iron pipe for air lines. This system was easier to install and looks great on the wall.

I am recommending this system to friends and customers as well as planning to replace airlines in my home garage.

Yesterday I finished the airline project and fired up the compressor to check on leaks.

I started to install the MaxLine system about 3 weeks ago with just me and 3 Saturday. I went with the 100 ft 3/4" system for more volume and CFM and watched the video on YouTube to get the gist on installing the system. The installation was easy and repetitive, once you did one "drop down" you just repeat the process until you are done.

My system has 7 drops (coupler plug ins) with a... more

It's easy to use and easy to install! No leaks anywhere!

After buying a high quality compressor I had to invest in a good solid air system. Rapid Air gave me the ability to provide clean air, that looks professional and didn't cost me a arm and a leg.

Thanks for the great quality product!