iON Products BA-33M
iON Products BA-33M
iON Products BA-33M
Hover to zoom
1 Of 5
iON Products BA-33M
iON Products BA-33M

iON 1/3 HP Cast Iron Stainless Steel Sump Pump w/ Adjustable Vertical Float HP20142

Model:

BA-33M

Write A Review
$265.00
Free Shipping
  Learn More About Free Freight
Free Shipping
*This product qualifies for Free Shipping anywhere in the contiguous US. Accessories may ship separately. Items over 100lbs shipped via semi-truck, be sure to select "Lift Gate" to lower the product to the ground curbside. Remote area surcharges may apply, see our full shipping policy for more details.
Only 1 In-Stock
Ships Wednesday, Mar 20th
Shipping to60601

iON 1/3 HP Cast Iron Stainless Steel Sump Pump w/ Adjustable Vertical Float HP20142
iON 1/3 HP Cast Iron Stainless Steel Sump Pump w/ Adjustable Vertical Float HP20142
Model: BA-33M
$265.00
Accessories
Features
Specifications
Reviews
Product Q&A
How-To Articles
Manuals
Share

Recommended Accessories

Power Equipment Direct expert image
Expert Recommended Accessories Selected by Jim, our Expert
Required Accessories 9
These accessories are required to properly setup/install this product.
Optional Accessories 10

Features

Style

Primary

GPH

4080 Gallons

Switch Type

Vertical

  • Powerful & Efficient Submersible Pump
  • Ideal for heavy-duty sump applications
  • Cast Iron Stainless Steel Construction
  • Ensures years of reliable operation
  • Adjustable Vertical Switch
  • Reduce pump cycles in deeper pits or areas w/ higher water tables
  • Thermally Protected Motor
  • reduces overheating
  • Stainless Steel Screened Intake
  • Prevents debris from entering the pump
  • Poly Resin Top Cap and Handle
  • Made for easy installation and maintenance
  • Piggyback Pump and Switch Cord Assembly
  • Made for easy serviceability

Specifications

BA-33M
specs product image PID-2877
General Information
Product Category
Sump Pump
Base
Base Material
Cast Iron
Min Sump Basin Size
10 Inch
Motor
Voltage
120 Volt
Running Amps
4.5
Thermal Protection
Yes
Power Cord Length
10 Feet
Oil Free Motor
No
Starting Amps
12.9
Pump
Housing Material
Stainless Steel
Impeller Material
Plastic
Solids Handling Size
0.5 inch
Handles Solids
Yes
Float Type
Vertical Float
GPH @ 0 feet
4080
GPH @ 5 feet
3660
GPH @ 10 feet
3000
GPH @ 15 feet
2400
GPH @ 20 feet
1260
Discharge Port Size
1-1/2 Inch
Check Valve Included
No
Float On
Adjustable
Float Off
Adjustable
Manual Override
Yes
Submersible
Yes
Engine
Horsepower
.33 hp
Overview
Product Category
Sump Pump
Weight
29 Pounds
Made in USA
No
Consumer Warranty
3 Years
Product Length
7.9 Inches
Product Width
5.5 Inches
Product Height
12.5 Inches
UPC
6482605855560

Reviews

(116)
iON Products BA-33M Reviews & Ratings

Product Q&A

(24)
Expert avatar photo
Product Questions Answered by Jim, the Sump Pump Expert
My water softener wash tube discharges into my sump pit. Will the Storm Pro BA Series Pump hold up to the salt water in the pit?
Jim T 
from Ohio 
January 29, 2014
What does min. sump basin size mean?
John D 
from Massachusetts 
February 02, 2013
I would like to know how many watts a 1/3 or 1/2 hp sump pump has, because i was think of buying a portable generator in case the power goes off.
Tom B. 
from New York 
September 03, 2012
I understand that the BA-33M has a switch differential of 6-1/2 inches. Can I modify it with a longer rod to increase that differential and thus further cycling?
Ben 
from Ohio 
June 27, 2012
I don't know which model sump pump to purchase or which model is appropriate for my home. How do I go about doing that?
Harry  
from Illinois 
May 20, 2012
Is stormpro and sumpro made by the same company? Is your site says not made in the USA for stormpro, where is it made?
Dan 
from Indiana 
May 05, 2012
When setting the switch off point, how much of the pump (Storm Pro 33) should remain permanently submerged?
Ted 
from Indiana 
April 17, 2012
Can it pump water 16 feet high?
Paul 
from Ohio 
February 17, 2012
Is the Storm Pro Ba33m 1/3 HP UL inspected?
Gregory Speicher 
from Pennsylvania 
January 28, 2012
Re: the Storm Pro BA-33M 1/3 HP. Ok, I cannot visualize the set up for this pump. It looks like the cord goes under water and that does not look safe at all for a sump pump! I have a tub to line the hole it goes into and do you put both units under water? Or below the floor line and eventual water?
Richard Neva  
from New York 
January 16, 2012
Are pump and switch available with 15' or 20' cords?
Tim Walsh 
from California 
December 21, 2011
I was concerned that as often as our pump works I should have a replacement pump in case the primary fails and an alarm if the power goes out. i was thinking of a pump that is more quiet and then using our old one as a backup. i'm not sure if I like the idea of a battery backup. any suggestions?
Ells Snyder 
from Maryland 
December 10, 2011
I recently purchased a BA-33 sump pump. Is it necessary to drill a hole in the bottom of the discharge pipe? Also how do I install the switch on the discharge pipe to maximize the run cycle? Is it adjustable? Finally- is it OK to go from 1 1/2" ABS pipe comming out of the discharge fitting to 1 1/4" id black plastic where it exits the house [about 7' above the pump] The 1 1/4" black plastic carries the water along and away from the foundation with a steady pitch for approx 30'.
John Szafranski 
from Massachusetts 
October 29, 2011
I recently purchased Stormpro BA-33M. I did not get the check valve. I picked up a check valve at a local plumbing outlet. The pump would not work at all with the valve installed, i have installed several of these and was careful to install the valve with the direction correct. I installed the pump without the check valve and it seems to work fine. Will this affect the life of the pump, or cause any problems? It has about a 10 ft. vertical lift and simply drains off into a ditch. Thanks.
Mark Ramsey 
from Tennessee 
June 21, 2011
Jim, Researching sump pumps and leaning towards the purchase of a StormPro BA33 with adjustable height switch. (good reviews) My question is can I purchase an additional switch for my secondary pump? I'm not sure what the model number is and the cost involved. Also, during my wet season, this pump will actuate every couple of minutes. I'm concern over how long the switch lasts! What do you recomend? Several of my pumps have failed due to the switch! Thank you in advance for your help. Joe
Joe Muscatello 
from Connecticut 
June 06, 2011
Hi Jim, I just bought a StomPro BA 33M sump pump.I would like for it to go "ON"at 9 or 9.5 inches.Where on the discharge pipe "height" in relation to the pump body do I attach adjustable switch? At contact pt with float at top,midway of pump body? Thanks so much,Marvin
Marvin Yowe 
from New York 
May 11, 2011
Hello Jim, I have an old Zoeller sump pump that does not seem to be able to keep up with demand (possibly overheating). I have an 18" diameter by 18" deep hole and I would estimate during peak rain periods a need for a pump to remove up to 36 gallons per minute. This pump seems to be able to do 50 gallons per minute. Is the 1/3 HP StormPro a good choice or should I go to the Simer 3995 I'm considering? I can't determine the current horsepower on my Zoeller...
David Marshall 
from Indiana 
April 22, 2011
Hi Jim i have a single sump pump that is only in a 2x4 foot rectangle that they left out of the concrete when they built my house . it is open to the air and water is always about 6 inches below the surface. I have a single sump in there now that keeps it from entering the basement and there is a low spot that has another pump that sits on the surface and routes its water to the primary. I wanted to enclose the pump and also get something powerful enough to keep that water lever down. i also donot want to be fighting the water table if that is the issue. ( it is very high) what kind of pump , enclosure , and system would you recommend...thank you , Jason
Jason Craig 
from Massachusetts 
April 17, 2011
Jim, To take advantage of a deep sump pit and reduce the number of run cycles. Which pump would you recommend that has the greatest on/off differential? Thanks, Dan
Dan Fenstermaker 
from Minnesota 
April 05, 2011
i have a truck well that gets water, leaves and a small amount of other junk. i am in florida and the wet season can cause a mess i need a heavy duty pump
F. T. ESPOSITO 
from Florida 
March 31, 2011
Jim, What is considered continuous duty applications. My present pump can be on in as little as 1 min intervals. Has operated for several years as such. A True Value Master Mechanic pump. Afraid will one day quit. Reason for shopping for replacement.
Roger L Kopshina Sr 
from Pennsylvania 
March 06, 2011
How does the sump pump connect to the independent float switch, Does the pump plug into the switch and the switch plugs into the power?
Mark 
from New Jersey 
February 09, 2011
Would this pump be suitable for a 12' x 12' basement?
Cody Dix 
from Ohio 
January 10, 2011
Hi Jim. I know the float can be attached to discharge line. I'm wondering what the maximum On/Off points are. Looking to figure out how many inches of water will be pumped out per cycle. Thanks.
Charlie 
from New York 
January 05, 2011

How-To Articles

How To Pick The Perfect Pedestal Sump Pump
How To Pick The Perfect Pedestal Sump Pump
Pedestal sump pumps sit on a pedestal that keeps them out of the water. Unlike ...
Introducing Goulds Pumps
Introducing Goulds Pumps
Born, raised, and built in the U.S.A., Goulds Water Technology is an American m...
How To Pick The Perfect Sump Pump
How To Pick The Perfect Sump Pump
You'll hardly think about your sump pump until it's too late. If your sump pump...
Power Equipment How-To Library
Power Equipment How-To Library
Articles, Tips and Buying Guides from Our Experts

Manuals

 
Media Gallery
iON 1/3 HP Cast Iron Stainless Steel Sump Pump w/ Adjustable Vertical Float HP20142
iON Products BA-33M
iON Products BA-33M
iON Products BA-33M
Customer Review Images