Generac Power Management Module (PMM) 24V Starter Kit (2013+ Smart Switches)

Generac Power Management Module (PMM) 24V Starter Kit (2013+ Smart Switches)
Model: 6199
$59.99
In-Stock
Ships Wednesday, Jan 17th
Tax-Free (Except IL)
In-Stock No Sales Tax* (Except IL)$59.99Buy Now
In-Stock No Sales Tax* (Except IL)$59.99Visit Site
Sales Tax Extra $59.99Visit Site
No Sales Tax* (Except CA,GA)$59.99Visit Site
Sales Tax Extra $67.12Visit Site
In-Stock
Ships Wednesday, Jan 17th
Enter your ZIP Code below to see an estimated arrival time of delivery to your home or business.
*We currently CANNOT ship this product to Canada or any destination outside of the United States
Shipping Info
Shipping Info
Expedited Shipping
Expedited Shipping
  • Product Description
  • 4
    Reviews
  • 3
    Product Q&A
  • Recommended Accessories
  • How-To Articles
  • Manuals
Product Description
+
Features
Features
  • Generac Digital Power Management System
  • For Generac RTSY/RTSR 100-800 Amp Smart Switches
  • Not compatible w/ NEXUS, Older Non-NEXUS or 3P transfer switches
  • Field Installed
  • Required for use with PMMs in Generac Smart Switches
  • Loads Can Be Intelligently Managed
  • Enables the use of a smaller, more efficient generator system
  • Drops out larger, non-essential loads
  • When the generator is capable, loads are switched back on
  • Connect Up To Four PMMs Per Smart Switch
  • Enjoy more power use & flexibility from a smaller generator
  • Module is rated to handle up to (1) 50 Amp device (1 included)
  • Includes
  • (1) 24V Transformer
  • (1) 50A Power Management Module (PMM)
Specifications
Product Specs
Frequency
60 Hertz
Overview
Weight
5 Pounds
Product Length
7 Inches
Product Width
4.25 Inches
Product Height
3.75 Inches
Consumer Warranty
1 Year
UPC
696471061994
Features
Features
  • Generac Digital Power Management System
  • For Generac RTSY/RTSR 100-800 Amp Smart Switches
  • Not compatible w/ NEXUS, Older Non-NEXUS or 3P transfer switches
  • Field Installed
  • Required for use with PMMs in Generac Smart Switches
  • Loads Can Be Intelligently Managed
  • Enables the use of a smaller, more efficient generator system
  • Drops out larger, non-essential loads
  • When the generator is capable, loads are switched back on
  • Connect Up To Four PMMs Per Smart Switch
  • Enjoy more power use & flexibility from a smaller generator
  • Module is rated to handle up to (1) 50 Amp device (1 included)
  • Includes
  • (1) 24V Transformer
  • (1) 50A Power Management Module (PMM)
Specifications
Product Specs
Frequency
60 Hertz
Overview
Weight
5 Pounds
Product Length
7 Inches
Product Width
4.25 Inches
Product Height
3.75 Inches
Consumer Warranty
1 Year
UPC
696471061994
Product Specs
+
Specifications
Product Specs
Frequency
60 Hertz
Overview
Weight
5 Pounds
Product Length
7 Inches
Product Width
4.25 Inches
Product Height
3.75 Inches
Consumer Warranty
1 Year
UPC
696471061994
Reviews
(4)
+
Generac 6199 Reviews & Ratings
Product Q&A
(3)
+
I just want to make sure this item works the way I think it does before I order it. I want to control an electric hot water heater that is on the other side of the house from the transfer switch location. The water heater's branch circuit comes from a subpanel also located on the far side of the house. So can I locate the contactor near the water heater; run low voltage cable (only) between the contactor and the transfer switch (50-60') and assume that the normally open contacts are closed whenever utility power is present?
Rob Saccardo 
from Massachusetts 
November 21, 2013
Read Response +
Answer
The installation that you have described is exactly how these devices are intended to operate. Generac advises that these devices are installed as close to the electrical load that it will support as possible. The contacts are NC during utility operation and will become NO for five minutes upon the initial restoration of generator power.

You can find more information on this within the Owner's Manual which is provided in the following link;
PMM Owner's Manual & Installation Guide
Hide Response -
I can see the 6186 is a 2-pole contactor, which is required to disconnect both phases of a 240V load like an AC compressor. Are the contacts of the module "form C" or just simple "form A" contacts?
Tom Reynal 
from Texas 
October 14, 2013
Read Response +
Answer
Thank you for your inquiry....

Form designations are fairly old and rarely used now. The Generac PMM modules consist of a 2-Pole NO (Normally Open) relay and rated to control:

*Current - 50A resistive or 40A inductive
*Voltage - 600 VAC
*Motor Rating - 7-1/2 HP @ 240 VAC
*LRA - 240A @ 240 VAC
*Coil Voltage - 24 VAC (6.5 VA Holding)
*Enclosure UL type 3R
Hide Response -
If you use more than one PMM #6199 do you need additional 24 vokt transformers for them?
James Hunt 
from Arkansas 
August 19, 2013
Read Response +
Answer
Only one 24V start kit is required. So if you need more then one PMM you would initially purchase the PMM with start kit and then purchase the individual PMM's - Model 6186 alone. (Up to 3 Additional PMM's for a total of 4).

Initial PMM Model - 6199 (Includes 24V Start Kit)

6199

Additional PMM Model - 6186 (Up to 3)

6186
Hide Response -
Recommended Accessories
+
How-To Articles
+
Manuals
+
 
 
×
Generac Power Management Module (PMM) 24V Starter Kit (2013+ Smart Switches)
+
Reset View

Visit Power Equipment Direct on Facebook
View the Power Equipment Direct Twitter Profile Page
Follow Power Equipment Direct on Pinterest
View Power Equipment Direct YouTube Channel
View Power Equipment Direct on Blog
View Power Equipment Direct Tumbler
View Power Equipment Direct LinkedIn Company Profile